Skip to content

Run the whole pool from your phone, whatever brand you already own.

The Attendant controller, a grey enclosure with the Poolside Tech name on its lid, with a phone beside it showing the Poolside app

The Attendant® by Poolside Tech, installed in Kelowna and across the Okanagan.

Poolside Tech Authorized Dealer

Most automation is built to sell you one brand of equipment. The Attendant is built to run the equipment you already own.

The Attendant® by Poolside Tech runs pumps, heaters, salt systems, valves and lights from almost every major manufacturer. We install it in Kelowna and across the Okanagan, set it up around how you use the pool, and keep an eye on it after.

Illustration of what you see, not the Poolside app itself.
Two Attendant controllers, one with a blue lid and one with a grey lid, lying on a lawn
The Attendant

One controller for the whole equipment pad.

Pumps, heaters, salt systems, valves, lights and chemistry, from any major brand, run together from one app.

Works with what you already have

Pentair, Hayward and Jandy, plus Raypak, AquaCal, Waterway, Speck and more. Your pump, heater, salt cell and lights do not have to match each other, or the controller.

Heating that plans ahead

Tell it the temperature you want and when. It checks the forecast and how your pool has heated before, then starts the heater at the right time instead of running it all afternoon. It shows the estimated cost first, so you can cancel if it is not worth it.

See what the pool costs to run

Enter your electricity and gas rates and the app breaks energy use and cost down by device, with history graphs, so you can see exactly where the money goes and how much the automation is saving you.

Hear about problems before they get expensive

Alerts for a dirty filter, low water, a leak, a blocked line, or a pump, valve or salt cell that is not behaving. If a valve actuator fails, it shuts the pump down to protect it. Alerts go to your phone, and to us if you want us watching.

Chemistry on autopilot (optional)

Add the Chemistry Module and it monitors pH and ORP around the clock and doses automatically, speeding up the pump to mix and prevent staining, and holding off while the pool is in use. The Dual Chemistry Module covers a pool and a spa. NSF 50 listed.

Lights, music and water features

DMX lighting with 16 million colours, 20 dimming levels and up to 128 zones, custom light shows, and shows synced to Spotify. Older non-DMX lights run through relays. Valves handle spillovers, fountains and other features.

Keeps the water level right

Non-contact high and low level sensing with autofill, so the pool tops itself up and the pump is never left running a pool low. It logs every refill and alerts you if it detects a leak.

Guest and rental mode

Give a guest, house-sitter, short-term renter or teenager access with limits on features and maximum heat, and an end date. You keep full control.

Part of your smart home

Works with Amazon Alexa, Control4 and ELAN, alongside the Poolside app for iPhone and Android.

Filtration that adapts

Filter cycles are set by run time or turnover, and adjust to the real-time chemistry and the weather forecast instead of a fixed timer.

Freeze protection and cover detection

Freeze protection can be set feature by feature, and when an automatic cover closes, the features that should not run are switched off for you.

A record of who changed what

The history screen shows who pressed what and when, you or a technician. After a spa session or other one-off, it goes back to the normal schedule on its own.

A phone showing the Poolside app's energy usage screen, on a table next to a passport, car keys, sunglasses and a Poolside Tech cap

The Poolside app

Check on the pool from anywhere.

At work, at the lake or across the yard, the app shows what the pool is doing and lets you change it. Heat it for when you get home, see what it cost to run this month, or hear about a problem the day it starts.

  • iPhone and Android, plus Alexa
  • Energy use and cost by device
  • Alerts to your phone, and to us if you want
  • Guest access with limits

Already automated

Why switch from your current system.

  • Stop being locked to one brand

    Brand automation works best with that brand’s own pumps, heaters and lights, and a mixed pad usually means features go missing. The Attendant runs mixed equipment as one system, so your next replacement can be whatever is best value, not whatever matches.

  • Your existing panel can stay

    In a typical retrofit of an IntelliCenter, OmniLogic, AquaLink or similar system, the old panel stays on the wall as the power centre. Poolside’s conversion kit moves the relay connections over to The Attendant, with no tear-out and no rewiring every circuit.

  • Features older controllers never had

    Forecast-aware heating, energy cost per device, equipment diagnostics and dirty-filter detection. Most older controllers mainly run schedules. This one watches how the pool is actually doing.

  • It keeps getting better

    Poolside ships regular software updates that add features and support for new equipment, so the system is not frozen at the day it was installed.

Upgrading from a specific system?

Still on timers

What changes when you add automation.

  • No more trips to the equipment pad

    Pump schedules, valve changes, heater on and off, lights: all from your phone, or from the touchscreen at the pad.

  • A longer, cheaper swim season

    Heating that runs only when it needs to makes it realistic to swim comfortably in May and September in the Okanagan without paying to heat the pool all day.

  • Small problems stay small

    A clogged filter or a failing pump shows up as an alert, not as a green pool or a burnt-out motor.

  • Peace of mind when you are away

    Check temperature, chemistry and equipment status from anywhere, and know someone gets the alert if anything goes wrong.

Two sizes

Sized to the pool, not the other way round.

The Attendant

For most backyard pools, pool and spa combinations, and bigger equipment pads.

  • Touchscreen at the controller, plus the app
  • Comes with 2, 4, 6 or 8 high-voltage relays
  • Up to 50 variable-speed pumps, lights, salt cells and heaters
  • 5 automatic valve actuators
  • 5 heater outputs and 5 temperature or water level inputs
  • Expandable for larger installations

The Attendant Mini

For simpler pools that need fewer circuits but the same smart features.

  • Controlled from the app (no on-board screen)
  • 2 high-voltage and 2 low-voltage relays
  • Up to 25 variable-speed pumps and serial devices
  • 3 automatic valve actuators
  • 2 heater outputs and 2 temperature or water level inputs
  • Grows with up to 4 expansion units

Both run on 120 V or 240 V, connect over Wi-Fi or Ethernet (the Mini adds Bluetooth), come with two temperature sensors, and can take the optional Chemistry Module. Neither limits how many bodies of water it runs: pool, spa, fountains and more. We recommend the right one after seeing your pad.

How an install works

  1. Look at the pad

    We come out, go through your equipment and how you use the pool, and confirm every piece is supported.

  2. A written plan and quote

    Which model, whether chemistry makes sense, and exactly what gets connected. Nothing changes on install day.

  3. Install and setup

    We mount the controller, connect the equipment, sensors and valves, and set up schedules and heating around your routine. A licensed electrician makes the 120/240V connections under permit, as BC requires.

  4. Handover and support

    We walk you through the app and stay on as your dealer for remote diagnostics, updates and anything that acts up.

Kelowna & the Okanagan

Your local Poolside Tech dealer.

Simply Swim is an authorized Poolside Tech dealer based in Kelowna. Equipment is priced in Canadian dollars in the shop, and every install is planned, done and supported here, so there is someone nearby when something needs a look.

  • Kelowna
  • West Kelowna
  • Lake Country
  • Peachland

Common questions

What does pool automation actually do?

It replaces mechanical timers and trips to the equipment pad with one controller you run from your phone. Pumps, heater, salt system, valves and lights work on schedules you set, and the system watches temperature, chemistry and equipment health so you hear about problems early. The Attendant also plans heating around the forecast and shows what each device costs to run.

Will it work with my equipment?

Almost certainly. Poolside supports nearly every pump, heater, salt system, valve actuator and light from the major brands sold in roughly the last decade. It suits new builds, retrofits and custom setups alike. We check every piece on your pad during the site visit, before you commit to anything.

I already have Pentair, Hayward or Jandy automation. Do I have to rip it out?

Usually not. In most retrofits the existing panel stays as the power centre and The Attendant takes over the control side, which keeps the job faster and tidier. We confirm this on site because it depends on the panel.

Can I still control things at the equipment pad?

With the full Attendant, yes: it has a touchscreen on the controller. The Attendant Mini is controlled from the app only.

Do I need the Chemistry Module?

Not necessarily. It is most worth it if you are away often, rent the property out, or want the water held steady without testing it yourself. We will go over whether it makes sense for your pool.

Does automation replace regular pool service?

No, it makes service better. Automation keeps things running and flags problems between visits. If we also service your pool, we see those alerts too and can often diagnose a fault before we arrive.

What does it cost?

The equipment prices for every model and add-on are listed in the shop, in Canadian dollars before tax. Installation depends on what is on your pad and what gets connected, so it is quoted in writing after a site visit. Quotes are free.

Can I get Poolside Tech in Canada?

Yes. Simply Swim is an authorized Poolside Tech dealer in Kelowna, BC, and the shop lists The Attendant, The Attendant Mini and their add-ons in Canadian dollars. We install across Kelowna, West Kelowna, Lake Country and Peachland. If you are elsewhere in the Okanagan, ask.

Ready to automate your pool?

Tell us what is on your equipment pad (brands and models if you know them, or just send photos) and we will come back with what it would take.

Poolside Tech

The Attendant® and Poolside Tech are trademarks of Poolside Tech. Product details are from Poolside Tech and may change.

Call Book an automation consultBook a consult